Please enter verification code
Metallurgical Analyses of Welding Using a Developed Mini-Robot
American Journal of Mechanical and Materials Engineering
Volume 4, Issue 2, June 2020, Pages: 26-36
Received: May 10, 2020; Accepted: May 25, 2020; Published: Jun. 15, 2020
Views 396      Downloads 129
Oladebeye Dayo Hephzibah, Department of Mechanical Engineering Technology, Federal Polytechnic, Ado-Ekiti, Nigeria
Adejuyigbe Samuel Babatope, Mechatronics Engineering Department, Federal University, Oye-Ekiti, Nigeria
Kareem Biliyaminu, Industrial and Production Engineering Department, Federal University of Technology, Akure, Nigeria
Article Tools
Follow on us
This research work addressed the mechanical and microstructural properties of welded joints. The results show the minimum average hardness values as 133.83, 102.13, 103.42, 95.15, 96.78 and 117.50 for various mini-robot welded mild steel plates of thickness 0.5 mm, 0.6 mm, 0.7 mm, 0.8 mm, 0.9 mm and 1.0 mm, while the maximum average hardness values were as 145.67, 119.08, 113.28, 106.58, 113.42 and 137.75 respectively. Results of the research have shown that the robot welding samples produced are high in hardness. This is responsible for low tensile stress values that may also mean low mini-robot welded sample extension. The robot welding samples developed gave low tensile strain values and this was expected because the robot welding samples developed had high hardness, low extension and low tensile stress. The microstructural study shows that the welded mini-robot samples had more fine structure than coarse (which is more pearlite than ferrite). The built welding robot has also provided a wide range of welding speeds from experimentation, significantly less welding time, wide weld length. The built welding robot has a range of welding time (4.7-32.94s), welding speed starting at 4.41mm / s over the same range of 0.5-1.0 mm thicknesses for the mild steel plate and weld length. The thicker the mild steel plate, the lower the welding time and the higher the welding speed. This is valid when the built welding robot was used. The built welding robot worked very well and the results of Microstructural Analyses presented quality welds.
Metallurgy, Robot Arc Welding, Microstructure, Tensile Strength, Brinell Hardness
To cite this article
Oladebeye Dayo Hephzibah, Adejuyigbe Samuel Babatope, Kareem Biliyaminu, Metallurgical Analyses of Welding Using a Developed Mini-Robot, American Journal of Mechanical and Materials Engineering. Vol. 4, No. 2, 2020, pp. 26-36. doi: 10.11648/j.ajmme.20200402.12
Copyright © 2020 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License ( which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Charde, N. (2012a). Characterization of spot weld growth on dissimilar joints with different thicknesses. Journal of Mechanical Engineering and Sciences, 2, 172-180.
Charde, N. (2012b). Effects of electrode deformation of resistance spot welding on 304 austenitic stainless steel weld geometry. Journal of Mechanical Engineering and Sciences, 3, 261-270.
Charde, N. (2013). Microstructure and fatigue properties of dissimilar spot welds joints of aisi 304 and aisi 1008. International Journal of Automotive and Mechanical Engineering, 7, 882-899.
Kukiełka, L. (1989). Designating the field areas for the contact of a rotary burnishing element with the rough surface of a part, providing a high-quality product. Journal of Mechanical Working Technology, 19, 319-356.
Shah, L. H., Akhtar, Z., & Ishak, M. (2013). Investigation of aluminum-stainless steel dissimilar weld quality using different filler metals. International Journal of Automotive and Mechanical Engineering, 8, 1121-1131.
Lopez-Juarez, I., Rios-Cabrera, R., & Davila-Rios, I. (2010). Implementation of an intelligent robotized gmaw welding cell, part 2: Intuitive visual programming tool for trajectory learning.
Rafiqul, M. I., Ishak, M., & Rahman, M. M. (2012). Effects of heat input on mechanical properties of metal inert gas welded 1.6 mm thick galvanized steel sheet. IOP Conference Series:Materials Science and Engineering, 36 (1).
Rahman, M. M., Arrifin, A. K., Nor, M. J. M., & Abdullah, S. (2008). Fatigue analysis of spot-welded joint for automative structures. SDHM Structural Durability and Health Monitoring, 4 (3), 173-180.
Rahman, M. M., Bakar, R. A., Noor, M. M., Rejab, M. R. M., & Sani, M. S. M. (2008). Fatigue life prediction of spot-welded structures: A finite element analysis approach European Journal of Scientific Research (Vol. 22, pp. 444-456).
Rahman, M. M., Rosli, A. B., Noor, M. M., Sani, M. S. M., & Julie, J. M. (2009). Effects of spot diameter and sheets thickness on fatigue life of spot welded structure based on fea approach. American Journal of Applied Sciences, 6 (1), 137-142.
Yang, W. H., & Tarng, Y. S. (1989). Design optimization of cutting parameters for turning operations based on the taguchi method. Journal Material Processing Technology, 84, 122–129.
Talabi, S. I., Owolabi, O. B., Adebisi, J. A., Yahaya, T. (2014). Effect of welding variables on mechanical properties of low carbon steel welded joint. Advances in Production Engineering & Management. 9 (4): 181-186.
Didit Sumardiyanto and Sri Endah Susilowati (2019). Effect of Welding Parameters on Mechanical Properties of Low Carbon Steel API 5L Shielded Metal Arc Welds, American Journal of Materials Science, 9 (1): 15-21
Manning, R., Ewing, J. (2009). RACQ Vehicles Technologies. (2009). Temperatures in cars survey. RACQ Vehicles Technologies, 1-21.
Greyjevo, O. G. T. V. Z., & Metodo, A. I. T. (2009). Optimization of weld bead geometry in tig welding process using grey relation analysis and taguchi method. Materiali in tehnologije, 43 (3), 143-149.
Oladebeye D. H, 2Adejuyigbe S. B., 3Kareem B (2020). Predictive Model Development for Welding Mini-robot, International Journal of Engineering Development and Research, 8 (2): 275-288.
Oladebeye D. H., 2Adejuyigbe S. B., 3Ayodeji S. P (2020). Comparative Analysis of Mechanical Properties of Mild Steel Plates Welded with the Developed Welding Robot and Manual Electric Arc Welding, International Journal of Engineering Development and Research, 8 (2): 289-302.
Nuraini1, A. A., Zaina, A. S. and Azmah Hanim, M. A. (2014). The effects of welding parameters on butt joints using robotic gas metal arc welding, Journal of Mechanical Engineering and Sciences (JMES), Vol. 6, pp. 988-994.
Sumardiyanto, D., Susilowati, S. E., & Cahyo, A. (2018). Effect of Cutting Parameter on Surface Roughness Carbon Steel S45C. Journal of Mechanical Engineering and Automation, 8 (1), 1-6.
Maksuti, R. (2016). Impact of the Acicular Ferrite on the Charpy V-Notch Toughness of Submerged Arc Weld Metal Deposits. International Journal of Scientific & Engineering Research, 7 (8): 1149-1155.
Science Publishing Group
1 Rockefeller Plaza,
10th and 11th Floors,
New York, NY 10020
Tel: (001)347-983-5186