Physicochemical Comparison Between Recycled and Straight Run Polypropylene Yarn
American Journal of Polymer Science and Technology
Volume 3, Issue 4, July 2017, Pages: 70-75
Received: May 7, 2017;
Accepted: May 31, 2017;
Published: Jul. 25, 2017
Views 1875 Downloads 82
Abdalaziz M. Seddeg, Department of Chemistry, Faculty of Pure and Applied Science, International University of Africa, Khartoum, Sudan; Khartoum Petrochemical Company (KPC), Khartoum, Sudan
Mohammed Margany, Department of Industrial Chemistry, Faculty of Applied and Industrial Sciences, University of Bahri, Khartoum, Sudan
Omsalama A. Alhafian, Khartoum Petrochemical Company (KPC), Khartoum, Sudan
Hussain A. Hussain, Khartoum Petrochemical Company (KPC), Khartoum, Sudan
Mohammed Noraldeen, Khartoum Petrochemical Company (KPC), Khartoum, Sudan
Mohamed N. Abdalaziz, Department of Chemistry, Faculty of Pure and Applied Science, International University of Africa, Khartoum, Sudan
Follow on us
In this research, investigating the possibility of producing, processing and also characterization of polypropylene fiber and recycling polypropylene has been presented. For this purpose, PP powder and inorganic filler were mixed using a twin screw extruder and modified granule was produced. After producing as-spun filament yarns by spinning machine at the take-up speed of 2000 m/min, samples were drawn, textured and finally weft knitted. Physical and structural properties of as-spun and drawn yarns with constant and variable draw ratios were investigated. The experimental results revealed that the straight run PP yarn impact tolerance is higher than the recycled PP yarn. And both type of yarns could be compared by drawing process. The straight run and recycled polypropylene filament woven laminates performed better in terms of both tensile load and broken elongation, with slight decrease in broken elongation results.
Polypropylene, Fiber, Extruder Machine
To cite this article
Abdalaziz M. Seddeg,
Omsalama A. Alhafian,
Hussain A. Hussain,
Mohamed N. Abdalaziz,
Physicochemical Comparison Between Recycled and Straight Run Polypropylene Yarn, American Journal of Polymer Science and Technology.
Vol. 3, No. 4,
2017, pp. 70-75.
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/
) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Kostar, T. D. and Chou, T.-W., A methodology for Cartesian braiding of three-dimensional shapes and special structures. Journal of Materials Science, 2002. 37 (13): p. 2811-2824.
Tolosana, N., Lomov, S., Stuve, J., and Miravete, A., Development of a Simulation Tool for 3D Braiding Architectures. AIP Conference Proceedings, 2007. 907 (1): p. 1005-1010.
Shi, Y., Swait, T., and Soutis, C., Modelling damage evolution in composite laminates subjected to low velocity impact. Compos. Struct., 2012. 94 (9): p. 2902-2913.
Christoforou, A., Yigit, A., Cantwell, W., and Yang, F., Impact Response Characterization in Composite Plates—Experimental Validation. Applied Composite Materials, 2010. 17 (5): p. 463-472.
Hull, D. and Shi, Y. B., Damage Mechanism Characterization in Composite Damage Tolerance Investigations. Composite Structures, 1993. 23 (2): p. 99-120.
Miravete, A., 3-D textile reinforcements in composite materials. 1999: CRC Press.
Generation III Extended Cold Weather Clothing System (ECWCS). PM Soldier Equipment. October 2016.
Benedikt, G. M. and Goodall, B. L. (eds.) (1998) Metallocene Catalyzed Polymers, ChemTech Publishing: Toronto. ISBN 978-1-884207-59-4.
Sierakowski, R. and Newaz, G., Damage Tolerance in Advanced Composites. 1995: Technomic Pub. Co.
Biaxially Oriented Polypropylene Films. Granwell. Retrieved: 2012-05-31.