Study on Blending Modification of Metallocene Linear Low Density Polyethylene
Volume 5, Issue 7, December 2017, Pages: 529-533
Received: Dec. 28, 2017;
Published: Dec. 28, 2017
Views 1131 Downloads 98
Qiu Di, School of Materials and chemical Engineering, Hubei University of Technology, Wuhan, China
Xu Heng, Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan, China
Wang Peng, Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan, China
Li Xuefeng, Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan, China
Long Shijun, Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology, Wuhan, China
Follow on us
In recent years, with the rapid development of China's wire and cable industry, optical cable demand gradually increased, but the wire and cable water resistance is not good, and vulnerable to corrosion caused by the distortion of the optical signal, so the cable aluminum-plastic composite belt should be born. In this study, The aluminum-plastic composite tapes were hot-pressed with low density polyethylene (LDPE) or metallocene linear low density polyethylene (MLLDPE) and high density polyethylene (HDPE) to test their heat sealing strength and mechanical properties. The rheological study shows that the HDPE/MLLDPE blends and HDPE/LDPE blends have a linearity in the lgG'-lgω curve in the low frequency region, and the heterogeneous system is in the molten state. The tanδ value of the blends gradually increased with the increase of the MLLDPE content, which indicated that the viscosity of the blends became higher, which improved the process ability of blends. The TGA blend shows that HDPE has better heat resistance. The melting point of HDPE in HDPE/MLLDPE blends decreased with the increase of MLLDPE content, which indicated that the two had mechanical compatibility. In the HDPE/ LDPE blends, two melting peaks were found, which indicated that the HDPE and LDPE had different crystal structure compatibility, and they were more likely to crystallize separately.
Cable, Heat Sealing Strength, Compatibility, Crystallization
To cite this article
Study on Blending Modification of Metallocene Linear Low Density Polyethylene, Science Discovery.
Vol. 5, No. 7,
2017, pp. 529-533.
M. Zatloukal, J. De. Witte, C. Lavallée, et al. Investigation of PPA interactions with polymer melts in single layer extrusion and coextrusion flows [J]. Plastics, Rubber and Composites, 2007, 36(6): 248-253.
T. Hameed, I. A. Hussein. Melt miscibility and mechanical properties of metallocene LLDPE blends with HDPE: Influence of Mw of LLDPE [J]. Polymer journal, 2006, 38 (11): 1114-1126.
M. Zatloukal, J. De. Witte. Influence of process aids on zigzag type of interfacial instabilities in multilayer flows: theoretical and experimental investigation [J]. Plastics, rubber and composites, 2006, 35(4): 149-154.
Li Yuying (李育英), Liu Chenyang (刘琛阳), Sun Xun (孙逊), He Jiasong (何嘉松). Acta Polymerica Sinica (高分子学报) [J]. 2000, (6): 707-710。
J. Kim, D. H. Kim, Y. Son. Rheological properties of long chain branched polyethylene melts at high shear rate[J]. Polymer, 2009, 50(21): 4998-5001.
Xu Xiaoqiu (徐晓秋), Tang Demin (唐德敏), Feng Jianxin (冯建新), Zhang Shuangnan (张爽男), Yang Hua (杨桦). Polymer Materials Science and Engneering (高分子材料科学与工程) [J]. 1999, 15(2): 86-89。
Y. Fang, P. J. Carreau, P. G. Lafleur. Thermal and rheological properties of mLLDPE/LDPE blends [J]. Polymer Engineering & Science, 2005, 45(9): 1254-1264.
N. Q. Zhou, P. Zhang, H. W. Wu, et al. An electromagnetic dynamic film blowing technology for mLLDPE [J]. Journal of applied polymer science, 2006, 101(1): 83-89.
R. Ramanathan. T. D. Traugott, L. R. Novak, et al. Blow moldable propylene polymer compositions: U.S. Patent 6, 784, 252[P]. 2004-8-31.
S. H. Wasserman. Characterizing the Melt Relaxation Behavior of Metallocene Polyethylenes [J]. Metal Bearing Waste Streams: Minimizing, Recycling and Treatment, 1990: 185.
M. Ebara, T. Aoyagi, K. Sakai, et al. Introducing reactive carboxyl side chains retains phase transition temperature sensitivity in N-isopropylacrylamide copolymer gels [J]. Macromolecules, 2000, 33(22): 8312-8316.
F. Hemmati. H. Garmabi, H. Modarress. Phase behavior of polyethylene/ethylene vinyl acetate blends: studies on miscibility window, composition dependency of interfacial interaction and enhanced toughness [J]. Journal of plastic Film and Sheeting, 2014: 8756087914525962.
Y. Son. Crystallization Behavior and Mechanical Properties of High Density Polyethylene/metallocene catalyzed Poly (ethylene-co-octene) Blends [J]. Journal of the Korea Academia-Industrial cooperation Society, 2013, 14(6): 3108-3113.
H. Münstedt, F. R. Schwarzl. Thermorheological Behavior of Various Polymer Melts [M]. Deformation and Flow of Polymeric Materials. Springer Berlin Heidelberg, 2014: 453-467.
J. Z. Liang, L. Zhong. Characterization of elongation viscosity for polyethylene melts [J]. Colloid and Polymer Science, 2013, 291(7): 1595-1599.