Damping Properties of Aluminum/ Duralumin Multi-Layered Graded Structures Fabricated by Hot Rolling
American Journal of Physical Chemistry
Volume 6, Issue 5, October 2017, Pages: 97-102
Received: Mar. 13, 2017; Accepted: Mar. 23, 2017; Published: Nov. 28, 2017
Views 3189      Downloads 158
Author
Hideaki Tsukamoto, Department of Mechanical Engineering, Faculty of Science and Engineering, Hosei University, Tokyo, Japan
Article Tools
Follow on us
Abstract
This study aims to fabricate aluminum (A1050)/ duralumin (A2017) multi-layered structures with interface composition gradient by hot rolling, and investigate their nanoindentation properties, and macro-mechanical property such as damping. 2- and 6-layered aluminum/ duralumin graded structures with asymmetric lay-ups from one side of aluminum to another side of duralumin have been fabricated, which suffer from three different heat-treatments such as (1) as-rolled (no heat-treatment), (2) annealed at 400°C and (3) homogenized at 500°C followed by water quenching and aging (T4 heat treatment). Nanoindentation demonstrated higher hardness and elastic modulus correspond to higher Cu content in annealed and aged samples. Duralumin in annealed samples shows much lower hardness and elastic modulus than those in as-rolled and aged ones. For damping properties, 2-layered graded structures show higher values than 6-layered graded structures, which are lower than single layers of aluminum.
Keywords
Multi-Layered Structures, Functionally Graded Materials (FGMs), Internal Friction, Nanoindentation
To cite this article
Hideaki Tsukamoto, Damping Properties of Aluminum/ Duralumin Multi-Layered Graded Structures Fabricated by Hot Rolling, American Journal of Physical Chemistry. Vol. 6, No. 5, 2017, pp. 97-102. doi: 10.11648/j.ajpc.20170605.13
Copyright
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
References
[1]
J. E. Lee, D. H. Bae and W. S. Chung, “Effects of annealing on the mechanical and interface properties of stainless steel/aluminum /copper clad-metal sheets,” J Mater Process Technol, 2007, vol. 187-188, pp. 546-549.
[2]
Y. M. Hwang, H. H. Hsu and Y. L. Hwang, “Analytical and Experimental Study on Bonding Behaviour at the Roll Gap During Complex Rolling of Sandwich Sheets,” Int. J. Mech. Science, 2000, vol. 42, pp. 2417-2437.
[3]
X. P. Zhang, T. H. Yang, J. Q. Liu, X. F. Luo and J. T. Wang, “Mechanical properties of an Al/Mg/Al trilaminated composite fabricated by hot rolling,” J Mater Sci, 2010, vol. 45, pp. 3457-3464.
[4]
L. Chen, B. Jha, Z. Yang, G. G. Xia, J. W. Stevenson and P. Singh, “Clad Metals by Roll Bonding for SOFC Interconnects,” J Mater Eng Perform, 2006, vol. 15, pp. 399-403.
[5]
P. Mallesham, A. A. Gokhale and A. Dutta, “Interface microstructure and bond shear strength of aluminum alloy AA8090/AA7072 roll clad sheets,” J Mater Sci Lett, 2003, vol. 22, pp. 1793-1795.
[6]
I. J. Polmear, “Light Alloys, The Metallurgy of the Light Metals,” 3 rd ed. (Arnold Publishers, London, 1995) vol. 331, pp. 77.
[7]
M. Fujikane, D. Setoyama and S. Nagao, “Nanoindentation examination of yttria stabilized zirconia (YSZ) crystal," J Alloy Compound, 2007, vol. 431, pp. 250-255.
[8]
F. Gao, T. Takemoto, “Mechanical properties evolution of Sn-3.5Ag based lead-free solders bynanoindentation,” Materials Letters, 2006, vol. 60, pp. 2315-2318.
[9]
R. Gibson, “Damping characteristics of composite materials and structures,” J. Materials Engineering and Performance, 1992, vol. 1, pp. 11-20.
[10]
A. L. Araújo, P. Martins, C. M. Mota Soares, C. A. Mota Soares, J. Herskovits, “Damping optimization of viscoelastic laminated sandwich composite structures,” Structural and Multidisciplinary Optimization, 2009, vol. 39, pp. 569-579.
[11]
Z. Li, Y. L. Jia, N. Tang, M. Fang, N. Liu, “A novel laminate combined with elasticity and damping,” Journal of Materials Processing Technology, 2007, vol. 182, pp. 1-5.
[12]
D. J. Lee, D-H. Ahn, E. Y. Yoon, S. I. Hong, S. Lee and H. S. Kim, “Estimating interface bonding strength in clad metals using digital image correlation,” Scripta Materialia, 2013, vol. 68, pp. 893-896.
[13]
M. Kameyama, M. Arai, “Optimal design of symmetrically laminated plates for damping characteristics using lamination parameters,” Composite Structures, 2015, vol. 132, pp. 885-897.
[14]
G. Demeshkin, M. E. Kozeko, V. M. Kornev, and V. D. Kurguzov, “Damping characteristics of composite structural materials fabricated by winding,” Journal of Applied Mechanics and Technical Physics, 2001, vol. 42, pp. 169-173.
[15]
P. Cupial and J. Niziol, “Vibration and damping analysis of a three-layered composite plate with a viscoelastic mid-layer,” J. Sound Vibration, 1995, vol. 183, pp. 99-114.
[16]
J. Gao and Y. Shen, “Vibration and damping analysis of a composite plate with active and passive damping layer,” Applied Math Mech, 1999, vol. 20, pp. 1075-1086.
[17]
J. Zhang, R. J. Perez, E. J. Lavernia, “Documentation of damping capacity of metallic, ceramic and metal-matrix composite materials,” J Mater Sci, 1993, vol. 28, pp. 2395-2404.
ADDRESS
Science Publishing Group
1 Rockefeller Plaza,
10th and 11th Floors,
New York, NY 10020
U.S.A.
Tel: (001)347-983-5186